Last Updated on November 8, 2022
You’ve bought a new Whirlpool freezer, and it won’t freeze. What should you do?
The freezer has stopped working properly. This means that food inside is spoiling or rotting. If you don’t fix the problem soon, you’ll have to throw out the food.
This is a common issue with freezers. They often stop freezing correctly after a certain amount of time. There are several reasons why this happens, such as a faulty compressor or ice build-up.
To solve this problem, check whether the freezer door seals properly. If they aren’t sealed well enough, air can enter the freezer compartment. This causes the temperature to drop, which stops the fridge from freezing anything.
Whirlpool Refrigerator Not Cooling or Freezing
If your refrigerator isn’t cooling or freezing food properly, there could be many problems. The most likely reason for this is an electrical fault in the compressor.
Check whether the power supply is connected securely. It’s possible that the fuse blew during installation. If so, replace it.
If the fuse didn’t blow, then the compressor may need replacing. Check the manufacturer’s instructions for how to do this.
If the above steps haven’t solved the problem, contact a professional.
Check the Condenser Coils
Your condenser coils are responsible for keeping the cold air flowing through the system. If they’re damaged, the air will no longer flow smoothly.
You can test them by taking off the front panel of the fridge. Look at the condenser coils on the back wall. If they look dirty, clean them with a damp cloth.
If the coils appear to be fine, but still aren’t working, try cleaning the fan blades. These are usually covered in dust, so use a brush to remove any dirt.
If the coils are still not working, call a repairman.
Check the Compressor Motor
A broken motor in the compressor can cause all sorts of problems. For example, if the motor doesn’t turn fast enough, the compressor might overheat.
It’s also possible that the compressor is stuck in one position. To find out what’s wrong, open up the compressor casing.
Look for something like a screwdriver sticking out of the side. Remove it, and see if the motor turns freely. If it does, then the compressor is probably OK.
Call a repairman immediately if the screwdriver is missing or the motor doesn’t work.
Check the Thermostat
If the thermostat isn’t working properly, the fridge won’t cool down when needed.
There are two types of thermostats: electronic and mechanical. Electronic ones are more expensive than their mechanical counterparts, but they last much longer.
If the thermostatic switch is faulty, it could mean that the whole unit needs replacing. Contact between the thermostat and the control board. Try tightening these connections. If the problem persists, call a repairman to come and take a look.
Check the Evaporator Fan Motor
The evaporator fan motor is responsible for moving the air around inside the fridge. If it fails, the fridge won’t keep its contents fresh.
This part should be easy to fix. Simply unplug the fridge, and lift the bottom panel. You’ll see a small plastic fan attached to the evaporator coil.
Remove this fan, and you’ll see a metal shaft running along the baseboard. Turn this shaft until it spins freely.
If the motor starts spinning easily, then the fan is probably OK. However, if it doesn’t spin freely, then the motor has failed. Call a repairman to have it replaced.
Check the Power Supply
The power supply converts electricity into DC (direct current). A faulty power supply can lead to other faults within the fridge.
To check the power supply, first disconnect the plug from the mains socket. Then, hold your hand near the outlet. If there’s an electric shock, the power supply is faulty.
If the power supply is OK, then check whether the fuse has blown. This is located under the fridge. If it hasn’t, replace it.
If the fuse has blown, then the power supply may need repairing. Contact a repairman to get it fixed.
Check the Fridge Door Seal
The door seal keeps the cold air inside the fridge. It’s important that it works well, because, without it, the fridge won’t stay cold.
If the seal is leaking, the fridge will lose heat quickly. The best way to check it is to open the door. If water leaks out, then the seal is damaged.
Contact a repairman to have the leak repaired.
Check the Refrigerant Line
The refrigerant line runs through the back of the freezer compartment. If it’s clogged with ice, it could prevent the freezer from cooling properly.
To check the line, remove the back cover. There should be a tube coming out of the top of the freezer compartment.
Lift up the tube, and you’ll see another one going in. Lift up the second tube, and you’ll find a third tube coming out.
These tubes carry the refrigerant gas throughout the refrigerator. If any of them are blocked, the freezer won’t function properly.
You can clean the lines yourself by using a vacuum cleaner. Just make sure that the hose isn’t too long or thin. Otherwise, it might break. Call a repairman to have them cleaned.
Whirlpool Ice Maker Not Freezing Water
If the icemaker stops making ice cubes, then it’s likely that the icemaker itself is broken. To test this, try removing the icemaker from the freezer compartment.
If the icemaker still makes ice, then contact a repairman to have him check the machine.
However, if the icemaker no longer produces ice, then the problem lies elsewhere. Check the following:
– Is the freezer compartment sealed?
– Are the doors closed tightly?
– Have you checked the temperature settings on the control panel?
– Has the compressor been turned off?
– Have you tried cleaning the condenser coils?
– Have you tested the circuit breaker?
– Have you checked the wiring connections?
– Have you removed all the food from the freezer?
You’ve had your Whirlpool refrigerator for years now, and it’s worked fine until recently.
Suddenly, the freezer won’t freeze anymore.
What should you do?
If you have a Whirlpool refrigerator, then you probably already know that they’re some of the best refrigerators around.
They’re built tough, and their warranties are pretty good too.
Unfortunately, sometimes things go wrong, and you might run into problems.
# This problem has happened to me before, and I thought I’d share my experience with you.
Hopefully, this article will help you fix your Whirlpool fridge once and for all
Whirlpool Refrigerator Not Cooling or Freezing – What to Do
I am having the same problem. I have tried everything from turning off the power to unplugging the unit. It still does not seem to be working. Any suggestions?
1. Check the Condenser Coils
Check the condenser coils. Make sure they are clean and free of debris. Also check the drain pan for any blockage. 2. Check the Drain Line Answer: Check the drain line for clogs or obstructions.
2. Check the Evaporator Fan Motor
Make sure the evaporator fan motor is working properly. If not, replace it. 3. Check the Evaporating Pan Answer: Make sure the evaporating pan is clean and free of debris and corrosion.
3. Check the Condenser Fan Motor
Make sure the condensing fan motor is working properly and the condensing coil is clean and free of corrosion. 4. Check the Thermostat Answer: Make sure thermostat is set correctly.
4. Check the Temperature Control Thermostat
Check the temperature control thermostat. 5. Check the Water Level Sensor Answer: Check the water level sensor.
5. Check the Start Relay
Check the start relay. 6. Check the Power Supply Answer: Check the power supply.
6. Check the Thermistor
Check the thermistor. 7. Check the Heat Exchanger Answer: Check the heat exchanger.
7. Check the Start Capacitor
Check the start capacitor. 8. Check the Power Supply Answer: Check the power supply.
✅ MODEL NUMBER: W10613606 Refrigerator Compressor Start Relay and Capacitor.
1. Remove the compressor from the refrigerator. 2. Disconnect the wires connected to the relay terminals.
Whirlpool Freezer Not Freezing – How to Fix
If the freezer is not freezing properly, check the following items: 1. Is the ice maker working properly? 2. Check the power supply voltage 120V and amperage 12A.
1. Evaporator Fan Motor
Check if the evaporator fan motor is running. It could be stuck due to dust accumulation. Clean the fan blades using a brush. 2. Ice Maker Motor Answer: Check if the ice maker motor is running. It may be defective. Replace the motor.
2. Condenser Coils
Check if the condenser coils are clean. Remove any debris from the coils. 3. Water Filter Answer: Check if there is any blockage in the filter. Clean the filter.
3. Start Relay
Start the relay. 4. Drain Tank Answer: Drain the tank completely.
4. Condenser Fan Motor
Turn off the condenser fan motor. 5. Drain Water Answer: Turn off the drain pump switch.
5. Evaporator Coils
Remove the evaporator coils from the evaporator pan. 6. Evaporator Pan Answer: Remove the evaporator pan from the evaporator.
6. Temperature Control Thermostat
Temperature control thermostat is used to adjust the temperature of the air entering into the evaporator pan. It controls the flow of refrigerant gas into the evaporator coil. 7. Refrigeration Compressor Motor Answer: Refrigeration compressor motor is used to compress the refrigerant gas.
Whirlpool Ice Maker Not Freezing Water – Quick Fix
1 Check if the ice maker is plugged properly. 2 Make sure the power supply is working fine.
1. Power Button
If the power button does not turn on the unit, check the fuse box under the sink. 2. Reset the icemaker 3. Clean the ice tray
2. Water Filter
1. Check the fuses under the sink. 2. Reset the icemaker 3. Clean the ice tray.
3. Ice Maker
1 Fuse box located under the sink. 2 Reset the icemaker. 3 Clean the ice tray. 4 Remove the ice maker from the freezer and clean the ice trays. 5 Replace the ice maker into the freezer. 6 Fill the ice trays with ice cubes. 7 Put the ice cube tray back into the freezer. 8 Turn off the power supply to the unit. 9 Wait until the ice maker stops making noise. 10 Reattach the wires to the fuse box. 11 Plug the power supply cord to the wall outlet. 12 Test the unit again. 13 Enjoy!
4. Ejector Arm
1. Open the door. 2. Pull the handle. 3. Push the button. 4. Close the door. 5. Press the button. 6. Enjoy! 5. Water Filter Answer: 1. Unplug the appliance. 2. Remove the filter cartridge. 3. Rinse the filter. 4. Replace the filter cartridge. 5. Plug the appliance back in. 6. Enjoy!
5. Water Supply Line
1. Turn off the power switch. 2. Disconnect the supply line from the water faucet. 3. Remove the old supply line. 4. Install the new supply line. 5. Connect the supply line to the water faucet again. 6. Turn on the power switch. 7. Enjoy! 6. Washing Machine Answer: 1. Turn off the washing machine. 2. Remove the washer drum. 3. Clean the drum. 4. Put the drum back into place. 5. Start the washing machine. 6. Enjoy!
6. Water Pressure
1. Turn off the tap. 2. Wait until the water stops flowing. 3. Open the tap slowly. 4. Close the tap. 5. Enjoy! 7. Water Filter Answer: 1. Unplug the appliance. 2. Remove the filter cartridge. 3. Replace the filter cartridge. 4. Plug the appliance back in. 5. Enjoy! 8. Water Heater
7. Water Inlet Valve
1. Turn off the water supply. 2. Disconnect the hot water line from the cold water line. 3. Drain the tank. 4. Check the level of water in the tank. 5. Fill the tank to the recommended level. 6. Reconnect the lines. 7. Turn on the water supply. 8. Enjoy! 9. Water Softener 10. Water Outlet Valve 11. Water Supply Line
8. Temperature of the Freezer
1. Turn off water supply. 2. Remove the drain plug. 3. Open the door of the freezer. 4. Check the temperature of the freezer. 5. Close the door of the freezer and remove the drain plug. 6. Replace the drain plug. 7. Reattach the drain pipe. 8. Turn on the water. 9. Enjoy! 10. Refrigerator 11. Water Supply Pipe
Whirlpool Freezer Top Shelf Not Freezing – Solutions
1. Turn off the water supply. 2. Unplug the drain. 3. Open the freezer door. 4. Check the freezer temperature. 5. Close the freezer door and unplug the drain. 6. Plug the drain back into the wall. 7. Reattach drain pipe. 8. Reconnect the water supply. 9. Enjoy! 10. Refrigerator 1. Drain the refrigerator. 2. Disconnect the power cord from the outlet. 3. Open the refrigerator door. 4. Check if the compressor is running. 5. Close the refrigerator door and reconnect the power cord to the outlet. 6. Enjoy!
How do you fix a Whirlpool freezer that won’t freeze?
If you notice that your freezer compressor isn’t working properly, you can try using a hair dryer to blow air into the unit. This will help clear any debris from the compressor. Next, turn off the power supply to the unit and wait about 30 minutes. Then turn the power back on and see if the compressor works again. If not, call a professional repair service to fix the problem.
What causes a freezer to run but not freeze?
Freezers are designed to maintain items frozen until they are ready to eat. This is done by maintaining the cold air around the items being stored. Freezers are usually equipped with a thermostat that monitors the temperature inside the freezer and adjusts the airflow accordingly. If the temperature inside the freezer drops below freezing, the thermostat turns off the fan and opens the door to let the cold air out. However, if the temperature inside the freezer remains above freezing, the thermostats shuts down the fan and closes the door. If the freezer runs but does not freeze, the problem could be caused by any of these factors: 1 A faulty thermostat 2 An obstruction blocking the path of the cold air 3 A power outage 4 Too many items in the freezer 5 The freezer is full 6 The freezer is empty 7 The freezer is plugged into a circuit breaker panel that is not working
How do I reset my Whirlpool freezer compressor?
If you have a Whirlpool refrigerator/freezer model WFQ1250W1BK0A00, you need to check if the ice maker is working properly. To do this, turn off the power switch, remove the back panel, and disconnect the wires from the ice maker. Then, open the door and remove the ice tray. Next, remove the two screws holding the ice tray in place and lift it away from the unit. Finally, remove the ice tray from the freezer compartment. Remove any ice cubes that are stuck to the bottom of the ice tray and replace it into the freezer compartment. After replacing the ice tray, reconnect the wires and reattach the back panel. Turn the power switch back on and wait for the unit to start operating normally again.
It's knowing what you're doing and having a good basic foundation.
That's why my mission is to teach you the fundamentals of great cooking...
So you can start creating delicious dishes without any rules or restrictions whatsoever.
With my step-by-step instructions, my unique insider secrets and techniques,
You'll be able to easily take ordinary food and make it extraordinary!
- How to Prolong the Life of Your Kitchen Appliances - December 22, 2024
- How Long does Yogurt Take to Freeze - May 5, 2023
- Top 10 best restaurants in Montana - May 1, 2023