Last Updated on November 8, 2022
If you notice that your Kenmore refrigerator isn’t cooling properly, it might be because one of the condenser coils is clogged. This quick fix ensures that the fridge stays cool and runs efficiently.
To clean the condensers, follow these steps:
- 1. Turn off the power switch.
- 2. Remove the cover plate.
- 3. Unplug the unit.
- 4. Disconnect the wires leading out of the condenser coil.
- 5. Pull the wire away from the condenser coil. If necessary, use pliers to pull the wire away from the connector.
Kenmore Refrigerator Not Cooling – How to Fix
If you’re having trouble keeping your Kenmore refrigerator cold, it could be because the fan motor isn’t working properly. If the fan doesn’t spin, the compressor might not start up either. You’ll want to check the fan motors before checking out the condenser or evaporators.
The fan motor is located inside the freezer compartment. To open the door, use a screwdriver to pry off the plastic trim around the edge of the door. Once the door is opened, look for the white metal fan motor. If it looks like it needs cleaning, clean it with rubbing alcohol. If it still doesn’t work, replace the fan motor.
You’ll find the fan motor next to the evaporator coils. To access the coils, remove the bottom panel of the fridge. Remove screws holding the panel in place. Lift the panel up and slide it aside. Look for the black coils under the evaporator pan. Clean them with rubbing alcohol. Replace the panel and tighten the screws.
Condenser Fan
A condenser fan is responsible for cooling the compressor. If you notice that the fan isn’t turning freely, replace it immediately.
Condenser Coil
A dirty condenser coil can lead to overheating and failure of the refrigerator. To prevent this from happening, it is important to check the condenser coil regularly. This includes cleaning the coils with a damp cloth and checking the thermistor. If you notice anything unusual about the refrigerator, call a professional immediately.
Kenmore Refrigerator but Not Cooling – How to Repair
Check the start
Get a relay. It’s a tiny thing that attaches to the side of the refrigerator. Shake it gently. If it doesn’t turn easily, check the switch. Is it loose? Does it make a clicking noise when you shake it? You’ll know if it’s working properly.
If the start relay works fine, check the compressor. The clicking noise you hear is the compressor trying to start. This happens because the condenser coil is dirty. A dirty coil makes the refrigerant gas too thick to pass through the evaporator coil. Without the compressor there’s no cooling.
Clean the condenser coil
To clean the coil, take off the front panel. Remove the screws holding the cover down. Then pull out the old filter. Use compressed air to blow out the dust. Put the filter back in place. Screw the cover back onto the unit. Now run some water over the coil. Let it drip away. Repeat the process until the water runs clear.
Now, put everything back together. Make sure the wires are tight against the terminals. Reattach the cover. Turn the power knob to OFF. Start the refrigerator again.
Kenmore Refrigerator Not Cooling But Freezer Is Fine – How to Fix
If you’re having trouble keeping your Kenmore fridge cool, it could be because the condenser coil needs to be cleaned out. Here are some tips to help you fix the problem yourself.Fan
If you’re having trouble keeping your food frozen, it could be because your refrigerator isn’t working correctly. You might want to check out our guide to finding a good repairman.Damper
An air damper controls the flow of cold air coming out of the freezer into the refrigerator. An air damper works like a valve. When you open it, cold air flows through the opening. When you close it, the cold air stops flowing.
If the air damper isn’t working correctly, the temperature inside the refrigerator might become too warm. This causes food to spoil faster and makes the refrigerator less efficient.
You can fix this problem yourself by replacing the air damper.
The best way to check whether your air damper needs to be replaced is to take it off and see how well it closes. To do this, follow these steps:
- 1. Remove the cover plate from the front of the freezer compartment.
- 2. Lift up the door panel.
- 3. Unscrew the screws holding the air damper in place.
- 4. Pull the air damper out of the freezer compartment. Look for signs of wear and tear.
Check the Coils
Freezer coils freeze over time. This causes problems like the ones listed below. To check the defrost control board for freezers, place an ice cube in the freezer compartment. If it gets hot, the defrost control unit is faulty. A defrost control board controls the defrost cycle. It works by opening and closing the door during the defrost cycle.
A defrost control board is part of the defrost system. If it malfunctions, the defrost won’t work properly. Check all the parts of your refrigerator to make sure everything is working properly. Also look at the evaporator coils. They could be clogged or dirty. You might want to clean them yourself or call a professional.
Kenmore Refrigerator Compressor Running But Not Cooling – Fast Fix
A Kenmore Refrigerator running but not cooling could mean one thing: it’s probably because you have a faulty refrigerator compressor. This problem occurs when the fan blades are blocked or damaged, causing the compressor to run continuously without cooling anything.
If you notice the fridge isn’t cooling down, try checking the following things:
- 1. Is the fan blade turning smoothly? Are the blades free of debris or dust?
- 2. Does the fan make any noise while operating?
- 3. Is the temperature gauge working correctly?
- 4. Have you checked the connection of the fan to the compressor?
- 5. Has the power cord been disconnected from the outlet?
- 6. Turn off the electricity supply to the appliance
Kenmore Refrigerator Fan Running But Not Cooling
A Kenmore refrigerator isn’t cooling properly. This problem can occur due to a variety of issues. Here are some things you should check before calling a repair person.
- 1. Is the fan running? If it is, you’ll want to make sure there aren’t any obstructions around the blower assembly. You might have to look inside the freezer compartment to see if anything is blocking the air flow.
- 2. Make sure the thermostat is set correctly. If the temperature control knob isn’t working, the thermostat may be faulty.
- 3. Is the compressor operating normally? If the compressor doesn’t turn on, it could indicate a power supply issue.
- 4. Does the door seal work? If it does, you’ll want to check whether the gasket is damaged.
- 5. Have you checked the condenser fan blades? They’re located behind the front panel of the fridge. If they don’t spin freely, you’ll want to replace them.
- 6. Do the ice maker and water dispenser drain lines run clear? If they do, you’ll want to clean out any debris.
Kenmore Refrigerator Not Cooling: How to Fix Refrigerator Problems
Most common problem is the compressor runs too hot and needs to run cooler. This usually happens because the temperature setting is set too high. To fix it, you must lower the temperature setting. You can do this manually or automatically. Manual: Turn the refrigerator’s power switch off and wait 30 seconds. Then turn the switch back on. Automatic: Set the temperature control to the lowest setting. Wait 20 minutes. Then reset the temperature to the desired level.
A simple way to test whether fans are working properly is to turn all appliances in the house off except for the refrigerator. If the refrigerator makes noise, there’s likely a problem with the fan motors.
This is how you can easily fix all the problems when your Kenmore Refrigerator is not cooling.
You’ve got a Kenmore refrigerator that won’t cool down.
What should you do?
If your fridge isn’t cooling properly, it could mean that something is wrong with its compressor or evaporator coils.
The problem could also be caused by a loose connection between the evaporator coil and the fan motor.
To fix this issue, you’ll need to replace the evaporator coil and fan motor assembly.
This repair is relatively simple and shouldn’t cost much
Kenmore Refrigerator Not Cooling after Power Outage – How to Fix
Kenmore Refrigerator not cooling after power outage – how to fix If you have a Kenmore refrigerator, and it suddenly stops working, you probably know what to do. But if you’re wondering why your fridge isn’t cooling down, here’s a quick guide to help you figure out what’s wrong. First off, check the power cord. It could be loose or damaged. If you see any signs of damage, contact the manufacturer immediately. Next, check the fuse box. Make sure the fuses aren’t blown. If they are, replace them. Finally, check the thermostat. If it’s set to “cool,” turn it to “heat.” If it’s already set to “heat,” try turning it back to “cool.”
Kenmore Refrigerator Not Cooling at All – What to Do
When you hear the hum of your refrigerator, you know it’s running. But sometimes, the humming doesn’t happen. This usually happens because the compressor isn’t working properly. To fix this problem, you’ll need to open up the door and remove the bottom panel. Look under the compressor and make sure it’s plugged into the wall. If it’ s not, unplug it and plug it back in. Then, take the top panel off and inspect the coils. If they�re dirty, clean them using a vacuum cleaner attachment. Once you’ve cleaned them, put the top panel back on and close the door. Now, the refrigerator should start working again.
Condenser Fan
If your condensing fan is making noise, it could mean that something is clogged in the air filter. Check the air filter itself to see if anything is stuck in it. If it looks clean, check the motor itself. It could be that the motor is worn out. If the motor seems fine, try cleaning the blades of the fan. Cleaning the blades is easy. Just turn the fan upside down and spray it with compressed air. After doing this, turn the fan right side up and let it dry. If the noise still persists, replace the fan.
Evaporator Fan
A condensing evaporator fan is used to cool the air coming from the evaporator coil. This fan helps to remove moisture from the air passing through the evaporator coil. In order to reduce the noise level, you can install a silencer. Silencers are available in different sizes and shapes. You can choose the one according to your requirement.
Condenser Coil
A condensing evaporator fan works by drawing air across the surface of the evaporator coil. As the air passes over the coils, it picks up moisture from the coils. The air then flows into the return duct where it is cooled and returned back to the living space. Evaporator Fan Answer: An evaporator fan is a type of ventilation fan designed to move air over the evaporator coil. It is used to draw air over the coils of the cooling system to absorb moisture from the air.
Thermistor
A thermistor is a resistor whose resistance changes according to the temperature around it. Thermistors are widely used in electronic circuits because they can be easily integrated into other components.
Start Relay
Thermistors are resistors whose resistance varies with temperature. A thermistor is a type of variable resistor that is used to measure temperature. It consists of two electrodes separated by a thin insulating layer. One electrode is connected to a power supply and the other is connected to ground. As the temperature changes, the resistance between the two electrodes changes. This change in resistance is measured and converted into a voltage signal.
Start Capacitor
Part No.: W10602601, Pack of 2 End Capacitor Answer : Part No. : W10602602, Pack of 2
Temperature Control Thermostat
Part No.: W10301001, Pack of 2 Thermometer Answer: Part No.: W10401021, Pack of 2 Timer Answer:
Kenmore Refrigerator Beeping But Not Cooling – Fast Fix
Kenmore Washer Leaking Water – Repair Cost $200 Answer:
Kenmore Refrigerator Making Clicking Noise but Not Cooling – How to Repair
Kenmore Washing Machine Making Loud Noises – How to Repair Kenmore Dryer Making Loud Noise – How to Repair
Kenmore Refrigerator Not Cooling But Freezer Is Fine – How to Fix
If you hear loud noises coming from your refrigerator, freezer, washing machine, dryer, or any other appliance, it could mean that something is wrong with the unit. It is important to note that these appliances are very sensitive and if they are not working properly, they can be quite dangerous. To ensure that you get the right repair service for your appliance, you need to know what type of noise it is making. For instance, if you hear clicking sounds, it could be that the compressor is malfunctioning. If you hear banging sounds, it could be the door is stuck. If you hear grinding sounds, it could be a belt is broken. If you hear squeaking sounds, it could be lubricant leaking. If you hear rattling sounds, it could be loose screws or bolts. If you hear humming sounds, it could be electrical problems. If you hear clanking sounds, it could be metal parts rubbing against each other. If you hear hissing sounds, it could be gas leaks. If you hear creaking sounds, it could mean that the hinge pins are worn out. If you hear buzzing sounds, it could be air blowing into the fan motor. If you hear rumbling sounds, it could be an issue with the fan blades. If you hear squealing sounds, it could be bearings are wearing out. If you hear screeching sounds, it could be seals are damaged. If you hear thumping sounds, it could be water leaking. If you hear scratching sounds, it could be rusting. If you hear knocking sounds, it could be ice buildup. If you hear scraping sounds, it could be debris caught between moving parts. If you hear squeaky sounds, it could be springs are worn out. If your appliance makes any of these types of noises, it is imperative that you contact a professional repair technician immediately.
Air Damper
A damper is a mechanism used to regulate airflow. Air dampers are commonly found in furnaces, heaters, and air conditioners. In addition, they are used in ventilation systems. A damper regulates the flow of air by opening and closing a vent. This allows the user to control how much air flows through the system. Air dampers are typically made of metal and plastic. Metal dampers are usually constructed using cast iron, brass, copper, stainless steel, aluminum, or zinc. Plastic dampers are usually made of polypropylene, nylon, or polycarbonate. The most common types of air dampers are butterfly valves, louvers, and slats. Butterfly valves are circular discs that open and close when the valve handle is turned. Louvers are rectangular openings that allow air to pass through but prevent objects from passing through. Slats are thin strips of material that are placed across vents. They are used to block off areas of the vent.
Evaporator Coils
Coil type evaporators are used in refrigeration and air conditioning applications. Coil type evaporators are generally made of copper or aluminum. Copper coils are usually plated with tin or nickel to protect against corrosion. Aluminum coil type evaporators are usually coated with a protective layer of paint.
Defrost Timer
A defrost timer is a feature that allows you to set the length of time that the unit will run after the defrost cycle is completed. This feature is very useful if you are using a refrigerator with a freezer compartment. The defrost cycle will take longer than normal because the freezer door needs to be open during the defrost cycle. A defrost timer will allow you to turn off the power to the compressor while the defrost cycle is still running.
Check out these other articles on refrigerators not cooling for other brands…
Defrosting is a necessary part of maintaining a refrigerator. It prevents ice buildup and keeps the interior free from moisture. However, if the defrost cycle is set too frequently, it could lead to unnecessary energy consumption and shorten the life of the refrigerator. To prevent this, you can adjust the defrost setting manually. To do this, follow these steps: 1 Open the door of the refrigerator.
Kenmore Refrigerator Compressor Running But Not Cooling – Fast Fix
If the compressor is running but the unit isn’t cooling, chances are good that the evaporator coil is clogged. This usually happens because of debris build-up in the drain pan. The easiest way to clean the drain pan is to remove the drain pan and run hot water down the drain line. Make sure the drain pan is completely empty before cleaning it. Once the drain pan is cleaned, replace it and turn off the faucet. Let the system sit for about 10 minutes while the water drains out of the drain pan. After the water has drained, shut off the water supply and let the system cool down. Then, open the drain pan again and check the drain line for any debris. Clean the drain line using a pipe cleaner or wire brush. If the drain pan still doesn’t clear after cleaning, call a professional plumber to inspect the drain line. How to Find Out Why Your Kenmore Refrigerator Is Not Cooling
Kenmore Refrigerator Fan Running But Not Cooling
A refrigerator fan that runs but does not cool the interior of the refrigerator is caused by a malfunctioning thermostat. A thermostat controls the flow of electricity to the fan motor. It senses when the temperature inside the refrigerator reaches a certain point and turns the fan on. If the thermostat malfunctions, the fan will continue to operate even though the temperature inside the refrigerator remains below the set point. In addition, if the thermostat fails to sense the temperature inside the refrigerator, the fan will remain off until the temperature inside the refrigerator rises above the set point.
How do you fix a Kenmore refrigerator that is not cooling?
Kenmore fridges are built to last but if they get old they tend to stop working properly. It could be because of the compressor or the fan motor. If the compressor stops working then the refrigerator won’t cool down. To fix this problem you’ll need to replace the compressor. If the fan motor doesn’t turn on then the cooling system will not run. This is usually caused by a bad capacitor. A capacitor is a component that stores electricity. It’s located near the fan motor. Replacing the capacitor will solve the problem.
What would cause a Kenmore Elite refrigerator to stop cooling?
Kenmore Elite Refrigerators are built to last. However, if the compressor stops working, the unit will not cool properly. This problem is usually caused by a bad connection between the evaporator coil and the condenser fan motor. To fix this issue, turn off the power switch and remove the back panel from the freezer section. Remove the two screws holding the top plate in place. Then lift the top plate away from the freezer section. Next, remove the three screws holding the evaporator coil assembly in place. Finally, disconnect the wires connected to the evaporator coil and condenser fan motor. Replace the top plate and tighten the screws. After replacing the evaporator coil assembly, reconnect the wires and replace the back panel.
Why is my Kenmore fridge not getting cold?
Kenmore refrigerators are built to last, but sometimes problems arise that can lead to failure. One such problem is a leaky compressor. A leaking compressor can cause moisture to enter the evaporator coil, which can damage the coils. To repair this issue, you will need to replace the evaporator coil. This can be done easily by removing the access panel from the back of the refrigerator. Once the access panel is removed, remove the screws holding the evaporator coil in place. Then, lift off the evaporator coil. Next, remove the old evaporator coil and clean it thoroughly. Replace the new evaporator coil and reattach the access panel. Finally, reinstall the screws and tighten them down.
It's knowing what you're doing and having a good basic foundation.
That's why my mission is to teach you the fundamentals of great cooking...
So you can start creating delicious dishes without any rules or restrictions whatsoever.
With my step-by-step instructions, my unique insider secrets and techniques,
You'll be able to easily take ordinary food and make it extraordinary!
- How Long does Yogurt Take to Freeze - May 5, 2023
- Top 10 best restaurants in Montana - May 1, 2023
- 3 Ingredient Lemon Pie - March 27, 2022