Last Updated on March 16, 2022
Have you ever wondered why some refrigerators don’t come with water filters?
Is it because they cost too much or are they really necessary?
Well, today we’ll explain you how to change the filter in a KitchenAid refrigerator.
If you’ve never changed the water filter in a refrigerator before, then you might be wondering why you should bother.
After all, the fridge already has a built-in water filter.
The answer is simple: it won’t last forever.
And once it stops working, you’ll have to replace the entire unit.
: Changing the water filter in a KitchenAid fridge is pretty straightforward.
All you need is a screwdriver and a little patience
How Do You Know When to Change the Water Filter in a KitchenAid Refrigerator?
KitchenAid refrigerators have a filter system built into the refrigerator door. This filter system helps remove impurities from the water used to cool the refrigerator. It does this by filtering the water through a mesh screen. The mesh screen filters out any particles larger than 0.2 microns. These particles could include bacteria, viruses, and other harmful contaminants. You should change the water filter every six months. To know when to change the water filter in a KitchenAid refrigerator, follow these steps: 1 Turn off the power switch located near the back of the refrigerator.
How to Change the Water Filter in a KitchenAid Refrigerator – Step by Step Procedure
Step 1: Remove the two screws holding the door panel in place. Step 2: Lift the door panel away from the frame. Step 3: Pull the old filter out of the door. Step 4: Replace the new filter with the old one. Step 5: Screw the door panel back onto the frame. Step 6: Reinstall the two screws.
Locate and release the water filter
KitchenAid refrigerators have a water filter located under the refrigerator door. This filter helps remove impurities from the water used to cool the refrigerator. It also prevents bacteria from entering the refrigerator. To change the filter, follow these steps: 1 Unplug the refrigerator.
Remove the old filter
2 Remove the plastic cap on top of the filter. 3 Pull off the rubber gasket.
Attach the cap to the replacement filter
1. Remove the plastic cap from the top of the filter. 2. Remove the rubber gasket from the bottom of the filter. 3. Put the new filter into place. 4. Replace the rubber gasket. 5. Screw the plastic cap back onto the top of the filter 6. Tighten the screw until it clicks. 7. Turn the knob to lock the filter in place. 8. Clean the filter screen. 9. Reassemble the unit. 10. Test the unit. 11. Enjoy!
Remove protective covering
1. Remove the plastic cap. 2. Remove the metal ring. 3. Place the new filter into the old one. 4. Replace the metal ring. 5. Screw the metal ring back onto the bottom of the filter 6. Screw the plastic cap onto the top of the new filter 7. Tighten the screw. 8. Turn the knob to secure the filter in place. 9. Clean the filter screen 10. Reassemble the filter. 11. Test the unit. 12. Enjoy!
Reattach the water filter
1. Unscrew the metal ring from the bottom of the filter. 2. Take off the plastic cap. 3. Put the new filter into the hole. 4. Put the metal ring back on the bottom of the filter 5. Screw the metal band back onto the bottom of filter. 6. Screw the plastic caps back onto the top of the filter. 7. Tighten the screws. 8. Turn the knobs to secure the filter in position. 9. Clean the screen. 10. Reassemble. 11. Test the system. 12. Enjoy!
How to Change the Water Filter in a KitchenAid Refrigerator — Bottom Line
KitchenAid recommends changing the water filter every six months. To change the filter, follow these steps: 1. Remove the refrigerator door panel. 2. Remove the two screws holding the filter assembly in place. 3. Lift the filter assembly out of the refrigerator. 4. Remove the old filter. 5. Replace the new filter. 6. Install the filter assembly. 7. Replace the door panel.
you will like this post on waterline installation
Water line installation is not difficult but requires proper planning and preparation. It is important to know how many fixtures you have in your house and where they are located. This information will help you determine if you need to install a new water main or simply replace existing pipes.
How do I remove the water filter from my refrigerator?
To change the water filter on your side by side refrigerator, follow these steps: 1 Remove the door panel from the front of the fridge 2 Unscrew the two screws holding the top of the water filter 3 Lift the top off 4 Disconnect the hose 5 Replace the new filter 6 Reattach the hose 7 Screw the two screws back into place 8 Replace the door panel 9 Close the door 10 Turn the power switch on 11 Wait about 30 minutes 12 Run a test 13 Enjoy!
How do I change the water filter in my KitchenAid refrigerator?
You should change your refrigerator filter every six months. This is because the filters trap bacteria and other contaminants from the air. It is important to know how much water you need to drain after changing the filter. To calculate the amount of water you need to drain, multiply the total volume of the filter in cubic inches by 0.5. For instance, if the filter is 3 cubic feet, you would multiply 3 x.50 = 1.5 gallons. To determine the volume of the filter, measure the length, width, and height of the filter. Then divide these measurements by 2.54 to get the cubic inches.
How do I flush my refrigerator water line?
Flushing the refrigerator water line is a simple process. First, turn off the power to the refrigerator. Next, remove the door panel from the back of the refrigerator. Remove the two screws holding the door panel in place. Then, pull the door panel away from the refrigerator. Finally, disconnect the water supply line from the wall outlet. Once the water supply line is disconnected, reconnect it to the drain pipe located near the bottom of the refrigerator. Reconnect the water supply line to the wall outlet. Turn the power back on to the refrigerator. Now, the refrigerator water line is flushed.
How much water do I need to drain after changing my fridge filter?
KitchenAid refrigerators have two filters, one located near the top of the door and another located under the ice maker. To replace the filters, remove the access panel from the bottom of the door and lift off the filter plate. Remove the old filter and place it in a trash bag. Then, install the new filter by placing it into the opening and pushing down until it snaps into place. Replace the access panel and tighten the screws.
How do you change the water filter on a side by side refrigerator?
To remove the water filter from your refrigerator, simply unscrew the cap on the top of the unit and pull off the filter. Once the filter is removed, replace the cap and tighten it down.
It's knowing what you're doing and having a good basic foundation.
That's why my mission is to teach you the fundamentals of great cooking...
So you can start creating delicious dishes without any rules or restrictions whatsoever.
With my step-by-step instructions, my unique insider secrets and techniques,
You'll be able to easily take ordinary food and make it extraordinary!
- How Long does Yogurt Take to Freeze - May 5, 2023
- Top 10 best restaurants in Montana - May 1, 2023
- 3 Ingredient Lemon Pie - March 27, 2022