Last Updated on November 8, 2022
The Electrolux brand is one of the most well-known appliance brands in North America. With over 30 years of experience creating high-quality products, it is no surprise that many people trust the name. However, there are some issues with certain models that can cause the unit to stop working properly. One of the most common complaints about the Electrolux brand is that the refrigerators do not cool enough.
If you notice that your fridge is not cooling, here are three things you can try to help resolve the issue.
1. Check the Thermostat
Check to make sure that the thermostat is set correctly. If the temperature setting is set too low, the compressor won’t run long enough to keep the food cold. A good rule of thumb is to set the thermostat to 50 degrees Fahrenheit lower than the desired temperature inside the refrigerator. For example, if you want to store food at 40 degrees Fahrenheit, set the thermostat at 36 degrees.
2. Make Sure There Is Enough Airflow
Another thing to check is whether there is adequate airflow throughout the entire refrigerator. If the fan isn’t moving air around, it won’t circulate the cold air. To test this, open up the door and see if the fan is running. If it isn’t, turn off the power switch and wait 10 seconds. Then, shut the door again and watch the fan start spinning.
3. Test the Compressor
Checking the oil level in the compressor is a good way to ensure that the compressor is working properly. If the oil level is low, then it may mean that the compressor isn’t getting enough airflow. You should check the oil level before using the compressor again. If the oil level seems fine, then you might want to consider replacing the compressor filter.
Replace the fan motor located at the back of the compressor. If the fan motor doesn’t spin freely, then it could be damaged. You’ll need to take the fan motor apart to make sure everything is working correctly. Once you’ve confirmed that the fan motor works, you can put it back together.
Problems that lead to Electrolux Refrigerator Not Cooling
1. The compressor is faulty. Check the fuse box.
2. There are ice crystals inside the evaporator coil. Unplug the unit and clean it out.
3. The temperature sensor is malfunctioning. Replace it.
4. The thermostat is defective. Disconnect the wires from the thermostat and reconnect them to another part of the system.
5. The fan motor is broken. Replace it.
6. The water valve is leaking. Turn off the power and unplug the unit. Remove the cover and look for water leakage. Clean the area around the water valve.
Solutions if Electrolux Refrigerator is Not Cooling
If you’re having trouble cooling your fridge down, it could be because of something simple like dust buildup inside your unit. Or maybe there’s a problem with one of your fans or coils. Electrolux recommends checking the following items to determine what might be causing your fridge not to work properly:
1. Clean out the filters on both sides of the evaporator fan motor. This includes the air filter and the condenser filter.
2. Make sure the temperature sensor is working correctly. If the temperature stays too high or low, check the thermostat settings to make sure they are correct.
3. Is the compressor running? Turn off the power switch and wait 10 minutes. Then turn the power back on and try again.
4. Does the door seal around the front of the refrigerator seem loose? Tighten it up.
5. Are the doors closed tightly? You can do this by pulling on the handles.
6. Is the freezer compartment free of ice build-up? Remove any ice cubes and wipe away any frost.
Other things to consider if your Electrolux Refrigerator Not Cooling
Evaporator Fan Motor
The evaporator fan is one of the most important components in refrigerators. This device draws cool air over the evaporators and spreads it throughout the unit. If the fan motor is malfunctioning, it will affect the flow of air inside the refrigerator. A faulty fan motor could cause ice buildup inside the unit, which can lead to water damage.
To fix a faulty fan motor, follow the steps listed above. First, remove the clip, blade and wire harness from the old fan motor. Then insert the new one and remount the fan blades and clips. Finally, reattach the wires to the new fan motor.
Evaporator Coils
The evaporator coil is the part of the refrigeration system where water vapor condenses into liquid water and absorbs heat. This happens inside the refrigerator compartment. When the coils freeze up, there is less room for the moisture to form ice crystals, which causes the compressor to work harder. As a result, the temperature rises and the refrigerator becomes warmer.
Condenser Fan
The condenser fan helps keep the refrigerant flowing smoothly throughout the system. When you turn off the power, the fan spins to circulate air around the condenser coil to make sure it stays cold. If the fan doesn’t spin properly, the coils won’t cool down fast enough and the temperature inside the unit will rise.
This component keeps the compressor and evaporator coils cool while they are working. If the fan isn’t running correctly, the compressor could overheat and shut off automatically. The compressor stops turning and the cooling function ends. You’ll know something is wrong when the compressor shuts off and the display reads “Low Refrigerant.”
Air Damper Control
The air damper controls how cold or hot the refrigerator gets. In most cases, the temperature inside the fridge stays constant. However, some fridges are set up to maintain different temperatures in different areas. For example, one area might keep things cold while another keeps things warm. This is done by opening and closing the damper.
If you notice that the temperature in your fridge fluctuates, check the air damper. You may find that it is stuck either partially opened or completely shut. In both cases, it needs to be replaced.
Defrost Timer
Check the timer to make sure it isn’t frozen up or broken. This is easy because you’ll see “defrosting” written across the face of the timer.
If you do find that the timer is frozen up or broken, don’t panic. Instead, simply follow these steps:
1. Remove the cover plate.
2. Turn the timer counterclockwise until the timer starts working again.
3. Replace the cover plate.
Thus, this is how you can quickly fix the Electrolux Refrigerator is it is not cooling properly
You’ve got a refrigerator that won’t cool down.
What should you do?
If you have an Electrolux refrigerator, you probably already know that it has a built-in thermostat.
This device helps regulate the temperature inside the fridge.
When the temperature gets too high or low, the thermostat automatically adjusts the compressor speed to bring the temperature back into range.
When the thermostat detects a problem, it sends a signal to the compressor motor.
The compressor then increases its speed until the temperature reaches the desired level
Electrolux Refrigerator Not Cooling But Freezer Works – How to Fix
If you have a refrigerator that won’t cool down, but the freezer works fine, check the thermostat. It’s possible that the thermostat isn’t working properly. To test if the thermostat is working correctly, open the door to see if the temperature changes. If not, replace the thermostat. If the problem persists, contact a professional service technician.
Evaporator Fan Motor
Check the evaporator fan motor. This is the part that turns on and off the air flow from the condenser coil. If the motor doesn’t turn on, it could mean that the fan blades aren’t rotating. Check the wiring harness to ensure that the wires are connected properly. If the fan blades still aren’t turning, the motor needs to be replaced. Condenser Coil Answer: Check whether the condenser coil is clogged. A clogged condenser coil can prevent the refrigerant from circulating through the system. Clean the coils using compressed air. If cleaning does not fix the issue, the condenser coil needs to be replaced. If the coils are dirty, clean them with a vacuum cleaner.
Evaporator Coils
If the evaporator coils are dirty, clean the coils using compressed air or a vacuum cleaner. Dirty coils can reduce the efficiency of the cooling system.
Condenser Fan
A condenser fan helps to circulate the air around the condensing unit. It keeps the condensate from dripping onto the floor and prevents moisture build up.
Air Damper Control
Air damper controls are used to regulate the flow of air into the evaporator coil. This allows the system to operate efficiently while preventing excessive humidity buildup.
Defrost Timer
Defrost timer is used to set the defrosting time. It is used to prevent frozen food from being thawed before the desired time. Door Lock Answer: Door lock is used to secure the door of the refrigerator.
Check out these other articles on refrigerators not cooling for other brands…
Refrigerator not cooling is a common problem faced by many people. This article provides information about how to fix this issue.
Electrolux Refrigerator Not Cooling – Solutions
If the refrigerator is not cooling properly, check if the compressor is working fine. If the compressor is working fine, then check if the fan is running normally. If the fan is not running normally, then check if the thermostat is set correctly. If the thermostat is not set correctly, then check if the door is closed properly. If the door is not closing properly, then check if the ice maker is working fine. If everything is fine, then check if there is any blockage in the drain pipe. If everything is fine but still the refrigerator is not cooling, then replace the evaporator coil.
Door Not Closed Properly
1 Check if the door is closed completely. 2 If yes, then check if the handle is locked.
Unit Not Plugged
If the door is not properly closed, the unit will not turn off. This is because the door is open. To fix this problem, you need to close the door. Then press the power button until the unit turns off. After that, unplug the unit from the wall outlet.
Thermostat Turned Down
To solve this problem, please check whether the thermostat is turned down. If the thermostat is set to low temperature, the unit will not shut off. Please adjust the thermostat to normal temperature.
Air Vents Blocked
If the air vents are blocked, the unit will not turn off. Please unblock the air vents.
Check the Compressor or Compressor Start Relay
Check the compressor relay. It is located near the top front of the appliance. Make sure the switch is set to "OFF" not "ON". This will prevent the compressor from running if the power goes out. Make sure the Compressor Is Not Running Answer: Turn off the main breaker and check the compressor. If it is running, turn off the compressor.
Check the Condenser Coils
Turn off the main breaker and remove the panel cover. Remove the condenser coils. Clean the fins and replace the coil. Check the Air Filter Answer: Open the air filter door and clean the filter. Replace the filter if necessary.
Check the Evaporator Fan
Open the evaporator fan door and check the fan blades. Clean the fan blades and replace the fan blade if necessary. Check Heater Element Answer: Turn off the circuit breaker and remove the panel covers. Disconnect the heater element from the power source. Clean the heating element and replace the element if necessary.
Check the Condenser Fan
Turn off the circuit breaker and open the condenser fan door. Remove the fan blades and clean the fan blades and replace them if necessary. Check Thermostat Answer: Open the thermostat cover and check the thermocouple wires. Replace the thermocouple wire if necessary.
Electrolux Refrigerator Freezer Not Cooling – What to Do
If the refrigerator is not cooling properly, check the following items: 1 Make sure the compressor is running. 2 Make sure the power switch is turned ON.
How do I reset my Electrolux refrigerator?
Fridge is a great invention but sometimes it fails to cool down quickly. It happens because of many reasons such as dirty coils, bad fan motor, blocked air vents, low refrigerant level, etc. If you notice any of these problems, please contact us immediately. We will fix it right away.
How do I reset my fridge to factory settings?
To reset your refrigerator to factory settings, follow these steps: 1 Turn off the power switch 2 Remove the back panel 3 Unplug the unit 4 Disconnect the wire harness 5 Press and hold down the reset button 6 Plug the unit back into the wall outlet 7 Wait 10 seconds 8 Reinstall the back panel 9 Reconnect the wire harness 10 Power on the unit 11 Close the door 12 Wait 20 minutes 13 Reset the unit 14 Power off 15 Open the door 16 Enjoy!
Why is my fridge not cooling fast?
If the door won’t open, try pushing the button again. If that doesn’t work, turn off the power switch and wait 10 minutes. Then turn the power back on and see if the door opens. If not, call customer service.
It's knowing what you're doing and having a good basic foundation.
That's why my mission is to teach you the fundamentals of great cooking...
So you can start creating delicious dishes without any rules or restrictions whatsoever.
With my step-by-step instructions, my unique insider secrets and techniques,
You'll be able to easily take ordinary food and make it extraordinary!
- How to Prolong the Life of Your Kitchen Appliances - December 22, 2024
- How Long does Yogurt Take to Freeze - May 5, 2023
- Top 10 best restaurants in Montana - May 1, 2023