Last Updated on November 8, 2022
Your Kenmore refrigerator has stopped working properly. The ice maker won’t produce enough ice cubes or the door won’t open or close. What should you do?
Your fridge may stop working due to a variety of reasons. One common problem is the control board inside the refrigerator. This part controls the temperature settings and other functions. If the control board fails, then the refrigerator stops working.
You can replace the control board yourself at home. Or, you can take it to a repair shop. In either case, you’ll need to follow some basic steps before starting the replacement procedure.
Where Is the Damper Control on a Kenmore Refrigerator?
The damper control is located in the back of the refrigerator compartment. You will find this switch under the bottom shelf. It’s usually marked “damper.”
![Kenmore Refrigerator Making Ice [Problems & Solutions]](https://www.forkandspoonkitchen.org/wp-content/uploads/2022/11/1-88.jpeg)
How Do I Replace the Damper Control?
To remove the damper control, first turn off the power supply by unplugging the unit from the wall outlet. Then, pull out the two screws that hold the cover plate over the damper control. Remove the cover plate and lift up the damper control.
Next, disconnect the wires connected to the damper control. Use an insulated tool such as a screwdriver to gently pry apart the terminals on each wire. Pull the wires away from the damper control until they are disconnected.
Now, carefully slide the new damper control into place. Make sure that the wires connect with the proper terminals on the new damper control. Reattach the cover plate and tighten the screws. Turn on the power supply again and test your new damper control.
If the damper control doesn’t work after replacing it, check for any loose connections. Also, make sure that the new damper control fits snugly in its opening.
What Are Some Common Problems With the Damper Control?
Damper controls have several different problems. They can fail because:
– The damper control is defective.
– There is corrosion on the contacts.
– The wiring harness is damaged.
– The damper switch is stuck in the closed position.
What Should I Look For When Replacing the Damper Switch?
When looking for a replacement damper switch, look for one that looks like the original. The old damper switches were made of plastic and had four small metal pins protruding from them. Newer models use a more durable material called ceramic. Ceramic is harder than plastic and resists damage better.
Also, be careful when removing the old damper switch. Don’t force it out. Instead, gently push it out using a flat object.
Replacement Parts for a Kenmore Refrigeration System
Replacement parts for a Kenmore refrigeration system include:
– Damper Controls
– Door Locks
– Ice Maker Compartments
– Water Filter Cartridges
– Thermostat Bodies
– Temperature Sensors
– Fan Motor Motors
– Condenser Fans
– Evaporator Fans
– Belt Drives
– Fridge Compressors
– Freezer Compressors
– Defrost Timers
– Humidifier Filters
– Air Ducts
Kenmore Refrigerator Control Board Reset
Resetting the control board requires removing the door panel and accessing the control board. To reset the control board, you must first determine which type of control board you have.
Control Boards
There are three types of control boards used in Kenmore refrigerators. Each has a unique number printed on the top of the board. These numbers correspond to the following:
- Type 1 – Model # KRCB1K
- Type 2 – Model # KRCM2K
- Type 3 – Model # KRCF3K
The control board is located behind the evaporator fan motor. If you don’t know what model you have, refer to the owner’s manual or contact a Kenmore service center.
Remove the screws holding the door panel in place. Lift the door panel off the cabinet.
Locate the control board. It should be covered by a black rubber gasket. Unscrew the two retaining clips at the back of the control board. Slide the control board out of the refrigerator.
Remove the six Phillips head screws that hold the control board in place. Carefully remove the control board.
Locate the reset button. This button will be located near the front edge of the control board. Pressing this button resets the control board.
Replace the control board. Replace the two retaining clips. Screw the control board back into place.
How Do I Reset the Control Board?
To reset the control board, press down firmly on the reset button until the control board lights up. Then release the button and wait about 10 seconds before pressing it again. Repeat this process as many times as necessary until the control board turns off.
If the control board does not turn off after five attempts, replace the control board.
Kenmore Refrigeration System Troubleshooting Guide
To troubleshoot your Kenmore refrigerator, follow these steps:
– Check the thermostat.
– Check the temperature sensor.
– Check the water filter cartridge.
– Check the condensation drain pan.
– Check the ice maker compartment.
![Kenmore Refrigerator Is Not Cold Enough [Solutions]](https://www.forkandspoonkitchen.org/wp-content/uploads/2022/11/2-87.jpeg)
– Check the air ducts.
– Check the evaporator fans.
– Check the defrost timer.
– Check the compressor.
– Check the freezer compressor.
– Check all electrical connections.
– Check the belt drive.
Kenmore Elite Refrigerator Control Board Green Light – What It Means
This light indicates that there is an error with the control board. The control board may need to be replaced. Contact a Kenmore service center for assistance.
Kenmore Refrigerator Control Panel Lights
Check the control panel lights. They indicate whether the refrigerator is running properly. Refer to the diagram below.
- Green All systems operating normally.
- Red One or more components malfunctioning.
- Yellow A component needs maintenance.
- Orange An internal problem exists.
- Blue A system failure has occurred.
- White No power available.
Note: The control panel lights do not always illuminate when the refrigerator is turned on. For example, if the refrigerator is plugged into an outlet but no electricity is flowing through the circuit, the control panel lights will remain dark. To check the status of the control panel lights, unplug the refrigerator from its power source. Turn the power switch on the wall to “off” position. Plug the refrigerator into an AC outlet. Wait 30 minutes. Turn the power switch to “on.” Observe the control panel lights.
Have you ever had trouble controlling your Kenmore refrigerator or freezer?
If so, you aren’t alone.
The problem seems to be widespread, affecting millions of consumers every year.
When was the last time you checked your fridge or freezer?
Chances are, it hasn’t been too long since you did.
And even though you might think you’re being careful, you probably don’t realize that you’re putting your food at risk.
Fridge and freezer problems can happen for a variety of reasons.
Some common causes include malfunctioning sensors, power surges, and faulty wiring.
In some cases, the cause isn’t clear
Where Is the Damper Control on a Kenmore Refrigerator?
Kenmore refrigerators have two different types of dampers. One type is located under the refrigerator door and controls the flow of cold air into the refrigerator. This damper is usually controlled by a lever located near the bottom of the door. The other type of damper is located in the back of the refrigerator and controls the flow of warm air from the freezer compartment to the rest of the refrigerator. This dampering is usually controlled by a switch located on the top of the refrigerator. How Do I Reset the Temperature Controls on a Kenmore Refridgerator? Answer: To reset the temperature controls on a Kenmore refrigerator, turn off the power to the unit and remove the access panel covering the front of the refrigerator. Then locate the temperature selector knob usually located on the right side of the refrigerator and move it to the desired setting. Turn the power back on and wait until the refrigerator warms up.
Kenmore Refrigerator Control Board Reset
To reset the temperature controls on your Kenmore refrigerator, first shut down the power to the unit. Next, remove the access panel covering on the front of the refrigerator and locate the temperature selector knob. Move the knob to the desired setting. Finally, turn the power back on and let the refrigerator warm up.
Kenmore Refrigerator Control Board Replacement
If you notice that the temperature display on your Kenmore refrigerator is not working properly, you can replace the control board. To replace the control board, first shut off the power to the unit and disconnect the wires from the old control board. Then, remove the access panel on the front of the fridge and locate the temperature selector switch. Turn the switch to the desired setting and reconnect the wires to the new control board. Replace the access panel and turn the power back on.
Kenmore Elite Refrigerator Control Panel Reset
To reset the temperature display on your kenmore elite refrigerator, follow these steps: 1 Remove the two screws holding the door panel in place. 2 Lift the door panel away from the refrigerator. 3 Press down on the top edge of the door panel until it snaps into place. 4 Press down on the bottom edge of the door panel to release the latch. 5 Slide the door panel toward the rear of the refrigerator until it clicks into place. 6 Press down on the lower edge of the door panel again to lock it in place. 7 Reinstall the screws and tighten them. 8 Reconnect the wiring harnesses to the new control board and test the temperature display. 9 Replace the door panel and reinstall the screws. 10 Test the temperature display again. 11 If the display still does not work, contact a service technician.
Kenmore Elite Refrigerator Control Panel Blinking – What to Do
Blinking lights indicate that something is wrong with the unit. It could be a problem with the compressor or the fan motor. This is usually caused by a loose connection or a bad wire. To fix this issue, first check if the light is blinking when the power switch is turned off. If it is, turn the power switch back on and wait for the light to stop flashing. If the light continues to flash after turning the power switch back on, call a professional repairman.
Kenmore Elite Refrigerator Control Board Green Light – What It Means
Green light indicates that the refrigerator is working properly. If the green light flashes, it means that the refrigeration system is not functioning correctly. In such cases, the refrigerator needs to be repaired immediately.
Kenmore Refrigerator Temperature Control Location
The temperature control board is located behind the door panel. To access the temperature control board, remove the door panel from the refrigerator.
Kenmore Refrigerator Ice Maker Control Light Blinking – Quick Fix
To fix the blinking light issue, follow these steps: 1 Remove the ice maker tray from the freezer. 2 Press the reset button on the back of the unit. 3 Replace the ice maker tray into the freezer. 4 Close the door. 5 Turn off the power switch. 6 Wait 30 minutes. 7 Reinstall the door panel. 8 Power on the unit. 9 After 15 seconds, press the reset button again. 10 Repeat step 8. 11 Close the door. 12 Turn off the power. 13 Wait 30 minutes. 14 Reinstall the door. 15 Power on the unit and wait until the display explains “Ready”. 16 Open the door. 17 Press the reset button. 18 Replace the ice maker trays into the freezer. 19 Close the door. 20 Turn off the power and wait 30 minutes. 21 Reinstall the door and turn on the power. 22 Wait until the display explains ‘ready’. 23 Open the door. 24
Kenmore Refrigerator Temperature Control Not Working – Solved
To solve the problem, first check if the thermostat is working properly. Check the wires connected to the thermostat. Make sure that the wires are not loose. Also, check the wiring connection between the thermostat and the compressor. If the wires are loose or disconnected, replace them. If the thermostat is still not working, try replacing the thermostat itself. If the problem persists, contact a professional technician.
Kenmore Refrigerator Control Panel Removal – Steps
To remove the refrigerator control panel, disconnect the power supply from the wall outlet. Remove the screws holding the back panel to the cabinet. Remove the screws holding back panel to the door. Remove the screws holding door to the cabinet. Disconnect the wires connecting the control panel to the circuit board. Pull the control panel away from the cabinet. Remove the old control panel. Replace the new control panel. Connect the wires to the new control panel. Reconnect the power supply to the wall socket. Screw the back panel to the door and cabinet. Screw the door to the cabinet.
How to Replace a Kenmore Refrigerator Dispenser Control Board
To replace the dispenser control board, follow these steps: Turn off the power supply to the unit. Remove the screws holding down the front of the control panel. Lift the control panel away from its mounting bracket. Remove the old control board. Install the new control board. Reinstall the screws. Plug the power cord into the wall socket.
How do I fix the control panel on my refrigerator?
Kenmore refrigerators have a diagnostic mode where you can check the status of the fridge. This feature allows you to see if the compressor is working properly or not. To access this feature, press the power button and hold it down until the light turns green. Then release the button and the lights will turn off. Press again and the lights will go back on and the unit will reboot.
What does ER 1f mean on Kenmore Elite refrigerator?
If you have a Kenmore refrigerator model KES7200, you can reset the control panel by pressing the power button until the display lights up. Then press the “reset” button located near the top right corner of the control panel. This will clear any previous settings.
How do you reset the code on a Kenmore Elite refrigerator?
Kenmore Elite refrigerators are built to last. But if something goes wrong with your appliance, you can easily fix it yourself. Here’s how to reset the code on your Kenmore Elite Refrigerator. 1 Turn off the power switch located near the back of the unit. 2 Remove the two screws holding the door panel in place.
How do I reset my Kenmore refrigerator control panel?
ER 1f indicates that the compressor is not operating properly. This could be caused by a power outage, a bad connection, or a faulty part. In any case, if you see ER 1f on your Kenmore Elite Refrigerator, contact Sears PartsDirect immediately.
How do you put a Kenmore refrigerator in diagnostic mode?
If you notice that the control panel on your refrigerator is not working properly, you can try to repair it yourself. First, turn off the power supply to the unit. Then remove the back panel from the front of the refrigerator. Remove the screws holding the control panel in place. Disconnect the wires connected to the control panel. Finally, replace the screws and reattach the control panel.
It's knowing what you're doing and having a good basic foundation.
That's why my mission is to teach you the fundamentals of great cooking...
So you can start creating delicious dishes without any rules or restrictions whatsoever.
With my step-by-step instructions, my unique insider secrets and techniques,
You'll be able to easily take ordinary food and make it extraordinary!
- How Long does Yogurt Take to Freeze - May 5, 2023
- Top 10 best restaurants in Montana - May 1, 2023
- 3 Ingredient Lemon Pie - March 27, 2022